Simulated flash twelve LED Lighting kit steering brake for 1/10 Scale model remote control vehicle Yokomo Tamiya HSP HPI AXIA·L RC4WD TRX

Flight model simulation of Tiangong 12-lamp remote control lamp Characteristics of flash lamp:
12 LED lights
Simulated lamp
Easy to use
Distant flash
Circuit board design improvement, HOSI power saving
Headlights white, blue tail lights, brake lights red, turn yellow
Suitable for 1/10 RC vehicles
Product specification:
Name: 12 LED Lighting System Kit
Material: Plastic
Number of LED bulbs: 12
Working current: 100mA
Input voltage: 4.8V?? 6.0V
Light color: white, red, yellow, blue
Connection mode: CH1 - servo
CH2 - Speed controller
CH3 - Receiver
Applicable to: 1/10 RC vehicle
LED cable length: about 300mm
Circuit board size: 53 * 33 * 15mm
Weight: 57.2g
Lamp Description:
Front light: 4 white LED lights
Connect the lighting system to the CH3 on the receiver: The transmitter can independently control one set of lights, and when the vehicle accelerates, the other set of lights will light up; The receiver is not connected to CH3: one set of lights is always on, and the other set of lights is on when the car accelerates.
Turn signal lamp: 4 yellow LED lamps
When the remote control changes direction, the indicator lights will flash synchronously.
Tail lights: 2 blue LED lights, 2 red LED lights
The blue light is always on. When the car accelerates or brakes, the blue light goes out. Only when braking, the red light comes on.
Installation method:
CH2 transmitter:
Connect the servo and ESC plugs to CH1 and CH2 on the lighting system, and then connect CH1 and CH2 to the receiver.
CH3 transmitter:
Connect the servo and ESC plugs to CH1 and CH2 on the lighting system, and then connect CH1, CH2, and CH3 to the receiver.
Full simulation - steering - intelligent linkage of front and rear lights - full simulation when your car turns left or right - steering - intelligent linkage of front and rear lights - when your car turns left or right
Turn signal (yellow) Follow left or right turn When your car brakes (red) Brake turn signal (yellow) Follow left or right turn When your car brakes (red) Brake
The interface between the accelerator and the steering gear in the vehicle light system The interface between the accelerator and the steering gear in the vehicle light system The interface between the accelerator and the steering gear in the vehicle light system
After a bit of integration, plug in the receiver and you can use it. After a bit of integration, plug in the receiver and you can use it
Various channel control installation methods Various channel control installation methods
Quantity: 12 LED lamps, including 3mm lamp caps for turn signal lamps and 5mm lamp caps for others Quantity: 12 lamps, including 3mm lamp caps for turn signal lamps and 5mm lamp caps for others
The details are as follows
Headlights: 4, white - 1. If connected to the third channel, the remote controller can control a group of headlights individually: 4, white - 1. If connected to the third channel, the remote controller can control a group of headlights individually
The switch of the light, and the other group of lights are always on when accelerating; 2. If the third channel is not linked, the switch for one of the lights will keep the other group of lights on during acceleration; 2. If the third channel is not linked: one of them
The group lights are always on, and the other group lights are always on during acceleration; The group lights are always on, and the other group lights are always on during acceleration;
Turn signal: 4, yellow one flashing synchronously with the remote control changing left and right directions; Turn signal: 4, yellow one flashing synchronously with the remote control changing left and right directions;
Tail lights: 4, of which 2 are always blue (blue lights will also go out when white headlights are lit) Tail lights: 4, of which 2 are always blue (blue lights will also go out when white headlights are lit)
"When braking, it turns off, and the other two lights up when braking in red. Normally, it turns off.", It turns off when braking, and the other two lights up when braking in red. It turns off when braking normally
Installation method: Installation method:
1. Remote control without a third channel (i.e. remote control). Modules without a control lamp set installed, such as Ledi 1. Remote control without a third channel (i.e. remote control). Modules without a control lamp set installed, such as Ledi
FS-GT2B) Insert the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then insert the linkage lamp FS-GT2B) Insert the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then insert the linkage lamp
The CH1 and CH2 on the group can be plugged into the CH1 and CH2 channels on the receiver; The CH1 and CH2 on the group can be plugged into the CH1 and CH2 channels on the receiver;
2. Remote control with a third channel (value remote control is equipped with a module to control the light group, such as the Ledi RC4G 2), remote control with a third channel (value remote control is equipped with a module to control the light group, such as the Ledi RC4G)
Insert the plugs of the steering gear and the electric regulator into CH1 and CH2 respectively, and then insert the CHI on the linkage lamp set Plug the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then connect the CHI on the linkage lamp set CH2 and
Plug CH3 into channels CH1, CH2, and CH3 on the receiver. Plug CH3 into channels CH1, CH2, and CH3 on the receiver
(Note: CH3 only needs to be plugged into the receiver) (Note: CH3 only needs to be plugged into the receiver)